How to Install Automatic Toilet Flusher For Tank Toilets OBA – i

Model I Product Name   Automatic Toilet Flusher For Tank Toilets QBA-I

Power   6AA Batteries
Flush Method   Auto-induction, Two-stage Flush (Low/Large Water Volume)
Detecti。n Rang 80 cm士10cm80 cm士10cm
Sensor:
Half Flush Timer: 10 – 60secs
Full Flush Timer: >60 secs
Maximum Flush Cycle : 10 secs
Applicable Toilet Tank Style: Side-pressing Type Toilet, Water Tank contains: 1: Flush Lever 2: Bead Chain 3: Flapper  4: Flush Valve

Sensorr Appearance and lnstruction
A· SETUP MODE (Left) – Adjust the Half /Low Flush cycle time by holding a Magnetic Wand against the right side.

(D) circular Magnetic Target until the desired water release is achieved. N。te the speed and distance of Flush Motor up/down cycle and adjust accordingly
B: PRESENCE DETECTION – A computerized human presence Sensor measures the “time at the toilet” and then activates a Flush Motor inside the tank which lifts the flush lever for either a half/Low-flush or full/Large flush as required.
C: LOW BATTERIES – It will flash when the batte叩is low, please replace the battery.
D:MAGNE口C TARGET (Half/Low Flush)
Note 1: After ρnished setup ，旷 the ha旷 flush water volume is insufficient or too much
(Based on personal actual demand), simple repeats the step of a叫justment. When completed setup , it needs to be reset the memory model of Sensor because of replacing the batteries.
Note 2: When computerized human-presence Sensor starts to measure the
“time-at-the-toilet” the Sensor Presence Detection LED will flash for 10secs
above(Maximum Flush Cycle: 10 secs) by standing in front of the Sensor and then activates a Flush Motor inside the tank which lifts in front of the Sensor and then activates a Flush Motor inside the tank which lift

Various parts

 

1Lift the toilet tank cover.
2,Tank internal structural Fig. 2 shows, A Overflow tube,B: Flapper, C:Flush handle.. If your Toilet instead of our example Fig.2, it still can be installed as long as you have above of the same parts
3,Take out the Tie Rod

4，Align Tie Rad to the Bolt Hole of Flush Motor.
5，Place the end of Tie Rod to inside square groove of Flush Motor.
6，Push the plug into the Bolt Hole t。 determine inserted in the end

7，Choose appropriate 0-Rubber Washer (thick or thin) t。而t Ove币。w Tube of Flush Valve
8，Put the 0-Rubber W目her itself on over the Ove币。w Tube, and place the smaller inner ring lip face up. Note interior angle of ring lip just place to the posibon of Ove币。w Tube gate.
9，• Place the F1xmg Rmg’s Triangle face up, then put the Fixing Ring on over the
0- Rubber Washer.

10,Button up the frame lock of Fixing Rmg to fix
11,Place the position of Flush Motor near to the top of Flapper of Flush Valve, and set Tie Rod towards Flapper in the same direcbon. Properly adjust the posibon of mulb direcbonal fixing hole of outer ring of Flush Motorto the Bait on the Fixing Ring if the parts posifon of tank is different from Fig 11
12,top down inserting the Blot into the Fixing hole

13,Hook the hook of the end 。f Bead Cham on the Flapper.
14,Completed.
15,Or can choose to hook the hook of the end of Bead Chain on the cham of Flush Handle.

16,Completed
17,Adust the length of Bead Cham appropriately and hook it into the U groove of Tie Rod.
18,Please note the shape of Bead Chain can not be too much bending as shown in Fig.18 after fixing it to the盯e Rod,to avoid failing to open Flapper or open too late

19,Correctly installed as shown in Fig. 19, as far as possible show st阳ight line. But the Flapper will not leak or slightly open for pulling too tight
20, Fetch out the Installation Demonstration Sticker, tear off the small seeker on inside dotted box and past it around the toilet used as sign of warning
21, Align the bottom edge of Installation Demonstration Sticker to the top of edge of toilet seat cover.

22,• Mount the Sensor using the attached foam type on the Back Plate by peeling
off tape, align to the bottom of Back Plate to the centra groove of installation Demonstration Sticker and stick on the wall and then tear off Sticker.
23, Remove the Sensor from its wall plate by sliding upward and off. Remove the Battery Cover with a small Philips screwdriver.
24, Install the 6 AA batteries and check that the silicone gasket inside the batteries compartment is in position

25,Reinstall the Screws of Battery Cover and replace the Sensor back on the wall
26,Mount the wire of Sensor into the back of Decorator  Cover and hook the groove of back plate with claw on the Decorator Cover
27,Cut the horizontal grooves on the Decorator Cover as appropriate when the Decorator Cover is too long during installing