{"id":6222,"date":"2016-04-02T01:57:40","date_gmt":"2016-04-01T17:57:40","guid":{"rendered":"http:\/\/www.toilet-valve.com\/?p=6222"},"modified":"2016-04-02T02:21:22","modified_gmt":"2016-04-01T18:21:22","slug":"how-to-install-automatic-toilet-flusher-for-tank-toilets-oba-i","status":"publish","type":"post","link":"https:\/\/www.toilet-valve.com\/how-to-install-automatic-toilet-flusher-for-tank-toilets-oba-i.html","title":{"rendered":"How to Install Automatic Toilet Flusher For Tank Toilets OBA – i"},"content":{"rendered":"

Model I Product Name \u00a0\u00a0Automatic Toilet Flusher For Tank Toilets <\/a>QBA-I<\/p>\n

Power \u00a0\u00a06AA Batteries
\nFlush Method \u00a0\u00a0Auto-induction, Two-stage Flush (Low\/Large Water Volume)
\nDetecti\u3002n Rang\u00a080 cm\u58eb10cm80 cm\u58eb10cm
\nSensor:
\nHalf Flush Timer: 10 – 60secs
\nFull Flush Timer: >60 secs
\nMaximum Flush Cycle : 10 secs
\nApplicable Toilet Tank Style:\u00a0Side-pressing Type Toilet, Water Tank contains: 1: Flush Lever 2: Bead Chain 3: Flapper \u00a04: Flush Valve
\n\"How<\/a>
\nSensorr Appearance and lnstruction
\nA\u00b7 SETUP MODE (Left) – Adjust the Half \/Low Flush cycle time by holding a Magnetic Wand against the right side.<\/p>\n

(D) circular Magnetic Target until the desired water release is achieved. N\u3002te the speed and distance of Flush Motor up\/down cycle and adjust accordingly
\nB: PRESENCE DETECTION – A computerized human presence Sensor measures the \u201ctime at the toilet\u201d and then\u00a0activates a Flush Motor inside the tank which lifts the flush lever for either a half\/Low-flush or full\/Large flush as required.
\nC: LOW BATTERIES – It will flash when the batte\u53e9is low, please replace the battery.
\nD:MAGNE\u53e3C TARGET (Half\/Low Flush)
\nNote 1: After \u03c1nished setup \uff0c\u65f7 the ha\u65f7 flush water volume is insufficient or too much
\n(Based on personal actual demand), simple repeats the step of a\u53ebjustment. When completed setup , it needs to be reset the memory model of Sensor because of replacing the batteries.
\nNote 2: When computerized human-presence Sensor starts to measure the
\n\u201ctime-at-the-toilet\u201d the Sensor Presence Detection LED will flash for 10secs
\nabove(Maximum Flush Cycle: 10 secs) by standing in front of the Sensor and then activates a Flush Motor inside the tank which lifts\u00a0in front of the Sensor and then activates a Flush Motor inside the tank which lift<\/p>\n

Various parts
\n\"How
\n<\/a>\u00a0\"How<\/a><\/p>\n

1Lift the toilet tank cover.
\n2,Tank internal structural Fig. 2 shows, A Overflow tube,B: Flapper, C:Flush handle.. If your Toilet instead of our example Fig.2, it still can be installed as long as you have above of the same parts
\n3,Take out the Tie Rod
\n\"How
\n<\/a>4\uff0cAlign Tie Rad to the Bolt Hole of Flush Motor.
\n5\uff0cPlace the end of Tie Rod to inside square groove of Flush Motor.
\n6\uff0cPush the plug into the Bolt Hole t\u3002 determine inserted in the end
\n\"How<\/a>
\n7\uff0cChoose appropriate 0-Rubber Washer (thick or thin) t\u3002\u800ct Ove\u5e01\u3002w Tube of Flush Valve
\n8\uff0cPut the 0-Rubber W\u76eeher itself on over the Ove\u5e01\u3002w Tube, and place the smaller inner ring lip face up. Note interior angle of ring lip just place to\u00a0the posibon of Ove\u5e01\u3002w Tube gate.
\n9\uff0c\u2022 Place the F1xmg Rmg’s Triangle face up, then put the Fixing Ring on over the
\n0- Rubber Washer.<\/p>\n

\"How<\/a>
\n10,Button up the frame lock of Fixing Rmg to fix
\n11,Place the position of Flush Motor near to the top of Flapper of Flush Valve, and set Tie Rod towards Flapper in the same direcbon. Properly adjust the posibon of mulb direcbonal fixing hole of outer ring of Flush Motorto the Bait on the Fixing Ring if the parts posifon of tank is different from Fig 11
\n12,top\u00a0down inserting the Blot into the Fixing hole
\n\"How<\/a>
\n13,Hook the hook of the end \u3002f Bead Cham on the Flapper.
\n14,Completed.
\n15,Or can choose to hook the hook of the end of Bead Chain on the cham of Flush Handle.<\/p>\n

\"How<\/a>
\n16,Completed
\n17,Adust the length of Bead Cham appropriately and hook it into the U groove of Tie Rod.
\n18,Please note the shape of Bead Chain can not be too much bending as shown in Fig.18 after fixing it to the\u76efe Rod,to avoid failing to open Flapper or open too late
\n\"How<\/a>
\n19,Correctly installed as shown in Fig. 19, as far as possible show st\u9633ight line. But the Flapper will not leak or slightly open for pulling too tight
\n20,\u00a0Fetch out the Installation Demonstration Sticker, tear off the small seeker on inside dotted box and past it around the toilet used as sign of warning
\n21,\u00a0Align the bottom edge of Installation Demonstration Sticker to the top of edge of toilet seat cover.
\n\"How<\/a>
\n22,\u2022 Mount the Sensor using the attached foam type on the Back Plate by peeling
\noff tape, align to the bottom of Back Plate to the centra groove of installation Demonstration Sticker and stick on the wall and then tear off Sticker.
\n23,\u00a0Remove the Sensor from its wall plate by sliding upward and off. Remove the Battery Cover with a small Philips screwdriver.
\n24,\u00a0Install the 6 AA batteries and check that the silicone gasket inside the batteries compartment is in position
\n\"How
\n<\/a>25,Reinstall the Screws of Battery Cover and replace the Sensor back on the wall
\n26,Mount the wire of Sensor into the back of Decorator \u00a0Cover and hook the groove of back plate with claw on the Decorator Cover
\n27,Cut the horizontal grooves on the Decorator Cover as appropriate when the Decorator Cover is too long during installing<\/p>\n","protected":false},"excerpt":{"rendered":"

Model I Product Name \u00a0\u00a0Automatic Toilet Flusher For Tank Toilets QBA-I Power \u00a0\u00a06AA Batteries Flush Method \u00a0\u00a0Auto-induction, Two-stage Flush (Low\/Large Water Volume) Detecti\u3002n Rang\u00a080 cm\u58eb10cm80 cm\u58eb10cm Sensor: Half Flush Timer: 10 – 60secs Full Flush Timer: >60 secs Maximum Flush Cycle : 10 secs Applicable Toilet Tank Style:\u00a0Side-pressing Type Toilet, Water Tank contains: 1: Flush …<\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_uf_show_specific_survey":0,"_uf_disable_surveys":false,"footnotes":""},"categories":[21],"tags":[],"_links":{"self":[{"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/posts\/6222"}],"collection":[{"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/comments?post=6222"}],"version-history":[{"count":5,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/posts\/6222\/revisions"}],"predecessor-version":[{"id":6238,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/posts\/6222\/revisions\/6238"}],"wp:attachment":[{"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/media?parent=6222"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/categories?post=6222"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.toilet-valve.com\/wp-json\/wp\/v2\/tags?post=6222"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}